Switch to full style
This area is for member suggested challenges using ProShow Gold only. See top thread for challenge rules.
Post a reply

Some Audio Tracks Have "Noise" in Them

Tue Feb 18, 2014 4:08 pm

In my 12 minute slideshow, I have eight different audio tracks. Four of them play perfectly; one had what I would call "very slight noise"; and three have lots of noise throughout the track.

For the four good tracks, one is 'wma' and three are 'mp3' files.

The track that had very slight noise was of type 'wma'.

The three tracks that have lots of noise were 'wav', 'wma', and 'wma', respectively.

Following the suggestions of a Photodex 'Help' page (http://kb.photodex.com/156/why-does-my-audio-file-sound-strange-in-proshow/), I converted the 'wma' file that had very slight noise to an 'OGG' file with sampling rate of 44.1 KHz. That eliminated the noise on that track.

I also converted the three files that had lots of noise to 'OGG' files with sampling rate of 44.1 KHz. The first of these now has a lot less noise, but it still is not good. The other two have just as much noise as before.

I then converted one of the really bad tracks to 'mp3'. There was no improvement. Still has lots of noise.

Can someone suggest a solution?

Thank you.

Re: Some Audio Tracks Have "Noise" in Them

Tue Feb 18, 2014 9:09 pm

Without knowing the exact details, there are two types of "noise" you are likely to encounter. The first is overdriving a digital signal - if you have the volume too high so you get clipping on the waveforms, you will get all sorts of strange crackling etc - turn the volume down to eliminate the clipping. The second is the track was noisy to start with - do the tracks play clean in media player for example? If not, then you have noise as part of the track and it is very difficult to get rid of that. We have run into issues with some mp3 files in the past where they were corrupted and they would crash Proshow, but I have not seen that for a while. If the noise is ONLY present in Proshow, but not when you play the tracks in an external player, then I'm not sure what is happening since I have not experienced that issue. Without actually hearing one of the problem ones, it is tough to make a better guess.

mikey

Re: Some Audio Tracks Have "Noise" in Them

Tue Feb 18, 2014 10:19 pm

I have now upgraded from ProShow Gold 6.0.3397 to 6.0.3410.

The audio tracks play with no crackling sound when I play them outside of ProShow.

I have tried turning down the volume and it makes no difference at all -- the crackling is still there.

Is there a way to upload a file to this forum? If so, I can record a few seconds of my slideshow and you could hear the crackling sound I am talking about.

Thank you.

Len

Re: Some Audio Tracks Have "Noise" in Them

Tue Feb 18, 2014 10:25 pm

Drop me a pm and I will give you my email address. We can go from there.

mikey

Re: Some Audio Tracks Have "Noise" in Them

Wed Feb 19, 2014 8:59 pm

Problem Solved!!

Mike explained to me that the problem I was having was called "clipping". He said that with digital audio tracks, if the volume is too high, the amplitude of the waveform will actually drop from the maximum value down to zero, causing the sound to appear to have static in it.

The solution was simple. In "Timeline" view of the waveform for the audio track, click on the waveform, after which a blue rectangular "box" will appear around the waveform. Place the cursor over the top edge of the blue box, see that the cursor changes to two horizontal parallel lines, and then "grab" that line (by left-clicking on the mouse), and drag it down slightly so that the waveform no longer touches the top (and bottom) of the blue box.

After I did that, the clipping was gone.

Re: Some Audio Tracks Have "Noise" in Them

Thu Feb 20, 2014 4:18 am

Mikey is a good person to know!!! He has helped me!!

Forrest

Re: Some Audio Tracks Have "Noise" in Them

Thu Feb 20, 2014 9:11 am

Gee thanks people :D

mikey

Re: Some Audio Tracks Have "Noise" in Them

Sat Jul 05, 2014 12:43 pm

Len_Jacobson wrote:Problem Solved!!

Mike explained to me that the problem I was having was called "clipping". He said that with digital audio tracks, if the volume is too high, the amplitude of the waveform will actually drop from the maximum value down to zero, causing the sound to appear to have static in it.

The solution was simple. In "Timeline" view of the waveform for the audio track, click on the waveform, after which a blue rectangular "box" will appear around the waveform. Place the cursor over the top edge of the blue box, see that the cursor changes to two horizontal parallel lines, and then "grab" that line (by left-clicking on the mouse), and drag it down slightly so that the waveform no longer touches the top (and bottom) of the blue box.

After I did that, the clipping was gone.


Had the same problem, followed your solution here and no more static ! Thanks :D
Post a reply